|
|
|
|
|
|
|
|
|
|
|
This video demonstrates how to use the wheel wrench to remove the wheel nut and wheel.
|
AD4 Terminal closed end for fuse panel
|
Terminal for master switch open end
|
|
|
|
|
|
|
|
|
|
|
|
|
Auto-Vac gasket set for Late Silver Ghost, Early British Phantom 1 up to Chassis 1 EF, and 20hp. Set includes two top cover assembly gaskets, Fuel filter gasket, and drain plug gasket. Gaskets are made from composite cork/neoprene and are suitable for modern fuels with or without ethanol.
|
Points ignition contacts for SP1 w/DeJon distributor. Sold in pairs only
|
Instruction plate for buffalo type wheel wrench used on Springfield cars
|
|
|
|
|
|
|
|
|
|
|
|
|
Air cleaner element for Springfield PI only. This is a modern replacement for the original element and a direct fit.
|
Rubber pad set for screw that attaches firewall to scuttle
|
Battery hold down for Optima 6 volt
|
|
|
|
|
|
|
|
|
|
|
|
|
Rubber Coupling Disc for dynamo drive and magneto drive
|
Bolt battery box cover and valence panels above running boards usually found on Springfield Silver Ghost and Springfield Phantom I. Reproduced in stainless steel. Priced per each.
|
Aluminum Washers are great for sealing connections involving fuel, oil, and coolant. Included are the most common sizes found on most Rolls-Royce and Bentley motorcars. The sizes and quantities are listed in the extended information tab.
|
|
|
|
|
|
|
|
|
|
|
|
|
Bracket for exhaust tail pipe. Reproduced in heavy gauge stainless steel.
|
Bracket for ignition wire loom includes E 73760 for aluminum head engines only P1, SP1
|
Bracket hot spot iron head Phantom I only sold in pairs
|
|
|
|
|
|
|
|
|
|
|
|
|
Cover for generator cut-out mounted on generator of Springfield Phantom I with Rolls-Royce made generator
|
Trilin Taillight lens reproduced in UV resistant plastic. This lens is Amber and is placed in the outside of a right mounted light.
|
Trilin Taillight lens reproduced in UV resistant plastic. This lens is Amber and is placed in the outside of a Left mounted light.
|
|
|
|
|
|
|
|
|
|
|
|
|
Trilin Taillight lens reproduced in UV resistant plastic. This lens is Red and is placed in the center bottom of the light.
|
inverter- converts 6 volt positive ground to 12 volt negative ground. Great for providing a power source to charge cell phones, GPS, overdrives, and much more that requires 12 volts
|
Wrench for Silver Ghost valve port caps, Springfield Phantom I engine oil drain plug and transmission oil filler plug. Reproduction
|
|
|
|
|
|
|
|
|
|
|
|
|
Pedal pad set Springfield Silver Ghost and Springfield Phantom I. Sold in pairs only
|
Cover for generator cut-out mounted on generator of Springfield Phantom I with Rolls-Royce made generator
|
Starter motor brush set for Springfield P1 six volt Rolls-Royce made unit
|
|
|
|
|
|
|
|
|
|
|
|
|
Connects shock absorber internal piston to the shock absorber arm. For Rolls-Royce manufactured hydraulic shocks only. Applies to front and rear Phantom 1 and early Phantom 2 rear shocks only. It is an assembly of F74566 and F74896. This is New Old Stock.
|
Headlight and Cowl light connector for drum style lights. These are single contact for single beam headlight and cowl light bulbs. They are reproduced just as the originals. Connector set includes one socket and one plug. Double contact connectors also available ,part number AD6.
|
Cap for Bijur tank. Reproduced in aluminum to replace the original zinc die-cast original that tends to fracture. Fits Springfield Phantom I early cars with threaded type cap only.
|
|
|
|
|
|
|
|
|
|
|
|
|
Headlight and Cowl light connector for drum style lights. These are double contact for double filament high/low beam headlight bulbs. They are reproduced just as the originals.They can also be used in the cowl lights for fitting double filament bulbs for turn signals. Connector set includes one socket and one plug. Single contact connectors also available AD7.
|
Water pump shaft and rotor assembly for Springfield Phantom 1. Shaft has been reproduced in stainless steel.
|
Rubber bumper mounts for tubular bumpers front and rear. Sold in pairs. Reproduced exactly as original with offset center hole for leveling
|
|