Banjo fitting for fuel lines and oil lines such as carburetor feed pipe, auto vac connection and some oil lines must be silver soldered on, fits 5/16" OD tubing 1/2" center opening

Seal- Bijur tank to firewall rubber fume seal. This part is actually a Post-War model part, however it is a good item to use on late Pre-War cars to help control fumes from entering the driver's compartment.

Auto-Vac gasket set for late P2 from 2 PY on. Set includes two top cover assembly gaskets, Fuel filter gasket, Auto-Vac control valve, and drain plug gasket. Gaskets are made from composite cork/neoprene and are suitable for modern fuels with or without ethanol.

Auto-Vac gasket set for early P2 to 1 JS. Set includes two top cover assembly gaskets, Fuel filter gasket, auto-vac control valve gasket, fuel tank control valve gasket, and drain plug gasket. Gaskets are made from composite cork/neoprene and are suitable for modern fuels with or without ethanol.

Auto-Vac gasket set for mid-production P2 from 1 JS to 2 PY. Set includes two top cover assembly gaskets, Fuel filter gasket, two auto-vac control valve gaskets, and drain plug gasket. Gaskets are made from composite cork/neoprene and are suitable for modern fuels with or without ethanol.

Attach Badges to your Badge Bar and Dress up your car

Bracket for small muffler connected to the carburetor induction heating exhaust system, reproduced in stainless steel

Bracket for small exhaust system (connected to the carburetor induction heating exhaust system) intermediate pipe support reproduced in stainless steel. Includes two E80277 as pictured

Bracket for small exhaust system, connected to the carburetor induction heating exhaust system, front pipe support reproduced in stainless steel.

Rubber pad set for screw that attaches firewall to scuttle

brass spade type terminal to be soldered on like original type, sold in sets of 6 only

Knob for instrument sliding light and ash tray. Threads onto a 1 1/6" x 16 TPI pull out. The OD is 1 1/2" and it is 9/16" high.

Bracket for main silencer (Muffler) reproduced in stainless steel

Rubber Coupling Disc for dynamo drive and magneto drive

Kit includes leather cup seals (2), gaskets, aluminum sealing washers, shaft seal, felt filter disc, and cap seal. This is for the large early type pump as shown in photos. This video shows the rebuilding process of the pump- https://youtu.be/cWWLc5UbYDA

Auto-Vac valve set reproduced to exact original standards. Set includes air valve, fuel valve, and mounting hasp.

Ignition rotor. Reproduced to the later design style to prevent spark from traveling down to the rotor post. Fits late British Silver Ghost using smaller Rolls-Royce type distributor as well as other Pre-War six cylinder models. Also fits AJS and AMS Series left hand drive Phantom II but requires that the end contact finger is flipped over.

Aluminum Washers are great for sealing connections involving fuel, oil, and coolant. Included are the most common sizes found on most Rolls-Royce and Bentley motorcars. The sizes and quantities are listed in the extended information tab.

Cover for starter relay switch for later 20/25 and later Phantom II on

Brush- set for dynamo late regulated P2,P3

Bracket for exhaust tail pipe. Reproduced in heavy gauge stainless steel.

Brackets for late style carburetor hot spot chamber. Reproduced in stainless steel, sold in pairs.

Autovac fuel control lever for early 20/25, late British Phantom 1, early Phantom 2

Locking plates for radiator mounts reproduced in stainless steel.

Trilin Taillight lens reproduced in UV resistant plastic. This lens is Amber and is placed in the outside of a Left mounted light.

Trilin Taillight lens reproduced in UV resistant plastic. This lens is Amber and is placed in the outside of a right mounted light.

Trilin Taillight lens reproduced in UV resistant plastic. This lens is Red and is placed in the center bottom of the light.

Trilin Tail Light Lens in Blue Plastic For Right Side

Trilin Tail Light Lens Clear Plastic Specify Right or Left for correct appearance, please

Coil for Pre-War cars to mount on original pedistal with two studs. The appearance of this coil is subject to change.